Toyana GE 180 ES-2RS plain bearings

C:15.5 mm; D:80 mm; B:20 mm; r1s (min):1 mm; a:18 mm; d2:50 mm; Static (Coa):87.4 kN; Dynamic (Ca):59.6 kN; r2s (min):0.3 mm; T:20 mm;

d:85.000 mm; Accessories:Two Shields & Snap-R; Basic Static Radial Load Rating Co:45000 N; B:22.00 mm; Grease Speed Rating Open/Shielded n1:5000 rpm; Oil Speed Rating Open/Shielded n2:6000 rpm; Fillet Radius ra:1.00 mm; D:130.0000 mm; Sealed Speed Rating n3:3000 rpm; Basic Dynamic Radial Load Rating

H:12 mm; dynamic Cr:17.820 kN; Pu:1.210 kN; static Cor:26.600 kN; d:17 mm; Grease:5 600 min-1; Oil:7 500 min-1; D1:19 mm; d1:35 mm; rs (min):0.6 mm;

da:149.225 mm; J min.:492.125 mm; Mass pillow block:125 kg; P120°:85.9 kN; End plug (suffix Y):EPR 18; Adapter sleeve assembly:SNW 34x5.7/8; ba:74.612 mm; Max. speed for PosiTrac Plus seal:950 r/min; Bearing:22234 CCK/W33; A2:242.887 mm;

D:45 mm; Specific static load factor K0:45 N/mm²; a:3 mm; Tolerance shaft:e7; Mass bushing:0.39 kg; α:124 °; Tolerance housing:H7; B:70 mm; Coefficient of friction µ min.:0.08; Permissible sliding velocity v max.:0.5 m/s;

Phase shift output signal:90 °; Period accuracy ±:4 %; Duty cycle:50 %; Phase shift output signal tolerance ±:30 °; Duty cycle tolerance ±:10 %; Number of pulses per revolution N:32; Mass sensor unit:0.07 kg; Limiting speed:5000 r/min; Cable connector type:Free cable end

B:33.00 mm; d:180.000 mm; Grease Speed Rating n1:2200 rpm; Basic Static Radial Load Rating Co:212000 N; Fillet Radius ra:2.00 mm; Oil Speed Rating n2:2800 rpm; Fillet Radius rb:1.00 mm; D:250.0000 mm; Basic Dynamic Radial Load Rating C:168000 N;

Fillet Radius ra:0.79 mm; D:34.9000 mm; Accessories:Two Seals; Shielded or Sealed B1:8.7 mm; Grease Speed Rating Open/Shielded n1:18000 rpm; Sealed Speed Rating n3:13000 rpm; Basic Dynamic Radial Load Rating C:6050 N; Oil Speed Rating Open/Shielded n2:22000 rpm; Width Plain B:7.1 mm; Basic Static Ra

Fatigue load limit Pu:8.7 kN; Static axial stiffnes:1380 N/µm; Number of attachment bolts:8; d:60 mm; H1:35 mm; D2:100 mm; Angle between bolts and thread holes α/2:22.5 °; Frictional moment:1 N·m; da min.:82 mm; d2:82.1 mm;

Basic dynamic load rating C:0.364 kN; Calculation factor f0:6.5; Mass bearing:0.0013 kg; Da max.:0 mm; Fatigue load limit Pu:0.005 kN; d2 ≈:4.6 mm; D:9.525 mm; Limiting speed:63000 r/min; Reference speed:130000 r/min; D2 ≈:8.2 mm;

Mass lock washer:0.005 kg; d2:36 mm; B:1.2 mm; d1:26 mm; M:18.5 mm; d:20 mm; f:4 mm;

T:32 mm; Db min.:144 mm; Ca min.:6 mm; Calculation factor e:0.46; Fatigue load limit Pu:31 kN; ra max.:2 mm; r1,2 min.:2 mm; rb max.:1.5 mm; a:32.451 mm; db min.:111.5 mm;

F:30 mm; r, r1,2 min.:0.3 mm; d:25 mm; Mass inner ring:0.046 kg; B:26.5 mm;

a:105 mm; Da max.:420 mm; Reference speed:1000 r/min; rb max.:3 mm; Calculation factor Y:1.4; r3,4 min.:4 mm; Fatigue load limit Pu:270 kN; Basic dynamic load rating C:1918 kN; Mass bearing:81.5 kg; D:440 mm;

d:300.000 mm; Fillet Radius ra:3.00 mm; Basic Static Radial Load Rating Co:375000 N; Grease Speed Rating Open/Shielded n1:1300 rpm; B:56.00 mm; Oil Speed Rating Open/Shielded n2:1600 rpm; Accessories:Two Seals; Sealed Speed Rating n3:800 rpm; Basic Dynamic Radial Load Rating C:270000 N; D:420.0000 m